Welcome Anonymous !

Everything you need to modify your ride
 

Interior Modifications

FG ICC (Radio) Mods and Hacking

Specific interior modification information for Ford BA and BF Series Falcons, Fairmonts, Fairlanes, LTD's and FPV models.

Postby SMASHPALACE » Wed Apr 11, 2018 7:51 pm

Hi guys,
First of all i would like to thank you all for the infomation on this thread about fitting a fgx sync system to a fg falcon .
I finally bite the bullet and bought a fgx icc a dash harness and a gateway , bcm custer and a few other bits .
I fitted the fgc harness and the gateway module with the new icc and it powers up with the key but when i start the car is get a u2300-51 code and it looks like i need to reprogram the abs control unit ???.does anyone know what scan tool will do that or should i buy a china ford vcm ?. Or failing that is anyone in Canberra or sydney i could pay to help me ?.
Ps the car is a mark 2 fg and i didnt have to reprogram the icc to get it to work.
Thanks again
Stuart
SMASHPALACE
Newbie Modder
 
Posts: 3
Joined: Thu Mar 15, 2018 6:46 pm
Has thanked: 0 time
Been thanked: 0 time

Postby JeffDav » Wed Apr 18, 2018 10:08 pm

SMASHPALACE wrote:Hi guys,
First of all i would like to thank you all for the infomation on this thread about fitting a fgx sync system to a fg falcon .
I finally bite the bullet and bought a fgx icc a dash harness and a gateway , bcm custer and a few other bits .
I fitted the fgc harness and the gateway module with the new icc and it powers up with the key but when i start the car is get a u2300-51 code and it looks like i need to reprogram the abs control unit ???.does anyone know what scan tool will do that or should i buy a china ford vcm ?. Or failing that is anyone in Canberra or sydney i could pay to help me ?.
Ps the car is a mark 2 fg and i didnt have to reprogram the icc to get it to work.
Thanks again
Stuart


Pretty standard for most things on the MK-2, you will need to perform all the ABS calibrations yaw, sas, ect, as far as i know this can only be done with the IDS, so either Ford or a china IDS.

Forscan cant do this.
JeffDav
Starting Ignition
 
Posts: 30
Joined: Sat May 27, 2017 2:29 pm
Has thanked: 0 time
Been thanked: 0 time

Postby SMASHPALACE » Thu Apr 19, 2018 7:54 pm

Hi JeffDav,
Thanks for the reply .
Iwas going to buy a chinese ids but they seam too cheap ie $200 Im worried i might brick one of the modules.
Has anyone had any success with the aliexpress chinese ids ?.
Thanks
Stuart
SMASHPALACE
Newbie Modder
 
Posts: 3
Joined: Thu Mar 15, 2018 6:46 pm
Has thanked: 0 time
Been thanked: 0 time

Postby JeffDav » Tue Apr 24, 2018 9:11 pm

i got a $130 ebay job and it works fine (Software was a lot of mucking around), you wont brick any modules performing any service procedures, diagnostics, resets, ect but defenatley would not use it for flashing any modules as they are known sometime to fail and if you brick the PCM its a tow to ford as the mk2 and fgx keys cant be programed without the ids and a ford login (Dealer only).
JeffDav
Starting Ignition
 
Posts: 30
Joined: Sat May 27, 2017 2:29 pm
Has thanked: 0 time
Been thanked: 0 time

Postby SMASHPALACE » Tue May 08, 2018 8:49 pm

Thanks again for the reply Jeffdav.
I got my chinese vcm2 and im have enormous issues with the software, but im hoping i get it sorted some time .
Then i can try the calabrations , im a little worried as i tryed a snapon solus and did the calabrations for the steering angle sensor and the yaw sensors but it didn't clear the codes.
SMASHPALACE
Newbie Modder
 
Posts: 3
Joined: Thu Mar 15, 2018 6:46 pm
Has thanked: 0 time
Been thanked: 0 time

Previous

Return to Interior Modifications

  • View new posts
  • View unanswered posts
  • Who is online
  • In total there is 1 user online :: 0 registered, 0 hidden and 1 guest (based on users active over the past 5 minutes)
  • Most users ever online was 151 on Fri Mar 03, 2017 1:44 pm
  • Users browsing this forum: No registered users and 1 guest