GM Technical Document Discussion
VE Instrument Cluster EEPROM Programming
Forum rules
To gain access to the Invite Only forum you must be invited by a member of that forum. That member will PM the mods or admins (NOT you) saying that they nominate you for access. THEY will be responsible for your actions. If you don't post and just leech info, you will BOTH be removed. Dont send a PM to the moderators or admins asking for access, you really dont want to see the result. If you submit information, you may simply be invited
To gain access to the Invite Only forum you must be invited by a member of that forum. That member will PM the mods or admins (NOT you) saying that they nominate you for access. THEY will be responsible for your actions. If you don't post and just leech info, you will BOTH be removed. Dont send a PM to the moderators or admins asking for access, you really dont want to see the result. If you submit information, you may simply be invited
by Pavi » Wed Sep 07, 2016 12:51 pm
Hi everyone
I m trying to put series 2 cluster in series 1 bcoz when I bought this car it has iq with navigation fitted and my old cluster shows the errors , I change vin and put it into the car but it shows abs and traction fault , can anyone help me out with this problem
Thanx for any kind of help
I m trying to put series 2 cluster in series 1 bcoz when I bought this car it has iq with navigation fitted and my old cluster shows the errors , I change vin and put it into the car but it shows abs and traction fault , can anyone help me out with this problem
Thanx for any kind of help
- Pavi
- Starting Ignition
- Posts: 20
- Joined: Wed Jan 06, 2016 12:57 pm
- Has thanked: 0 time
- Been thanked: 0 time
by Pavi » Wed Sep 07, 2016 12:54 pm
this is the 24c16 bin file from cluster
this clustr has been taken out from series sv6 ute manual
and my sv6 is manual too
this clustr has been taken out from series sv6 ute manual
and my sv6 is manual too
You do not have the required permissions to view the files attached to this post.
- Pavi
- Starting Ignition
- Posts: 20
- Joined: Wed Jan 06, 2016 12:57 pm
- Has thanked: 0 time
- Been thanked: 0 time
by jezzab » Wed Sep 07, 2016 2:17 pm
The config in the cluster wont match your car for a start (its setup for a 3.6L SIDI LFX engine). Thats why you get the ABS/ESP faults. The other thing is that Nav hasnt been enabled on the cluster your attempting to put in so its not going to fix these "errors" you say your original did. Nav wont even show at all.
How are you going to match the KM of your car??
How are you going to match the KM of your car??
Daily Ute - 2009 Holden VE SSV Ute Single Turbo (IQ, E3 Cluster, EDI) - 586rwhp
Drag Ute - 2002 Holden VU SS Twin Turbo - 1010rwhp [SOLD]
All VE/VF Module reprogramming. Remote programming with flash box
http://www.facebook.com/jsbperformance
Drag Ute - 2002 Holden VU SS Twin Turbo - 1010rwhp [SOLD]
All VE/VF Module reprogramming. Remote programming with flash box
http://www.facebook.com/jsbperformance
by jezzab » Wed Sep 07, 2016 6:56 pm
Pavi wrote:Thanx jezzab for reply
EEPROM is completely different than my old cluster , I m trying to work that out ,
So this series 2 cluster can't fit in my series 1
It has to be reprogrammed (config and KM). Not just a VIN change
Daily Ute - 2009 Holden VE SSV Ute Single Turbo (IQ, E3 Cluster, EDI) - 586rwhp
Drag Ute - 2002 Holden VU SS Twin Turbo - 1010rwhp [SOLD]
All VE/VF Module reprogramming. Remote programming with flash box
http://www.facebook.com/jsbperformance
Drag Ute - 2002 Holden VU SS Twin Turbo - 1010rwhp [SOLD]
All VE/VF Module reprogramming. Remote programming with flash box
http://www.facebook.com/jsbperformance
by Pavi » Wed Sep 07, 2016 11:15 pm
Ok , so I have to find the locations of kms and engine configuration . Ok is there any hint for that. EEPROM looks very difficult to understand bcoz 1st 3 lines has bytes r little bit tricky but i m on to it
- Pavi
- Starting Ignition
- Posts: 20
- Joined: Wed Jan 06, 2016 12:57 pm
- Has thanked: 0 time
- Been thanked: 0 time
by Pavi » Thu Sep 08, 2016 9:35 am
A little bit more about that the cluster from series 2 it has 028048 kms on it and the hex value should be 7F BF FF FD as but in this case eeprom does not have anything like that I can tell there is no 30 location like the white back clusters has . Looks more difficult but fingers cross
- Pavi
- Starting Ignition
- Posts: 20
- Joined: Wed Jan 06, 2016 12:57 pm
- Has thanked: 0 time
- Been thanked: 0 time
by TazzI » Thu Sep 08, 2016 11:08 am
Pavi wrote:A little bit more about that the cluster from series 2 it has 028048 kms on it and the hex value should be 7F BF FF FD as but in this case eeprom does not have anything like that I can tell there is no 30 location like the white back clusters has . Looks more difficult but fingers cross
Series1 and Series2 are different.
In all honesty, simply looking at the bin is not going to get you very far. Nothing is explained in the bin, so any one of the bytes could literally mean anything.
by Pavi » Thu Sep 08, 2016 11:27 am
Thanx tazzl
So I need a tech 2 for that and permission from tis to do that
To find Kms I think if I put the cluster in and drive the car for 200-300kms then take the eeprom reading and compare then may be a chance I can find the locations for that.
Thank u very much for correcting me
So I need a tech 2 for that and permission from tis to do that
To find Kms I think if I put the cluster in and drive the car for 200-300kms then take the eeprom reading and compare then may be a chance I can find the locations for that.
Thank u very much for correcting me
- Pavi
- Starting Ignition
- Posts: 20
- Joined: Wed Jan 06, 2016 12:57 pm
- Has thanked: 0 time
- Been thanked: 0 time